Home | Links | Contact |

Printed from www.nzmeccano.com

Top Home Bottom

Universal Joints Explained by Peter Stuart

(Author: Peter Stuart)

by Peter Stuart, Meccano Modellers Association Sydney Inc

Universal Joints Explained

by Peter Stuart, Meccano Modellers Association Sydney Inc


Universal joints (UJs) do not transmit constant rotary motion when driving through any angle other than a straight line (zero angle). When driving though an angle, a UJ imparts a cyclical faster and slower rotation to the driven shaft on each half revolution. The amount of this speed variation is dependent on the angle; the greater the angle, the greater the speed variation.


It can be calculated that at an angle of 25 degrees, a UJ rotating at 100rpm will cause the driven shaft to briefly reach a maximum speed of 110rpm in the first quarter revolution then drop briefly to 91rpm in the second quarter. This higher and lower speed variation will be repeated in the next two quarter revolutions.


Speed variation causes vibration and noise, and wears out the bearings. So what can be done?

1. Keep the angle of the UJ less than 25 degrees.
2. UJs should always be used in pairs so that three shafts are involved; input, intermediate and output. If the input and output shafts are made parallel then the angle though which the two UJs will be driving will be the same. Diagram 1 shows angle A to be the same for both UJs.
3. Align the forks of the two UJs so that the second UJ will cancel the speed variation caused by the first UJ. It is true that the intermediate shaft will rotate with speed variation, but not the output shaft. Correct alignment is achieved by having the forks aligned at each end of the intermediate shaft in line with each other. Diagram 1 shows this. Another way to picture the arrangement is that the second UJ is installed as a mirror image of the first.

Provided the angles through which the two UJs are operating is the same, another arrangement is possible as shown in Diagram 2. If a drive has to go around a corner of say 30 degrees, then two UJs can be used provided each joint turns the drive through half the angle; 15 degrees in this example (angle B in the diagram). The alignment of forks still has to be the same as described above. The intermediate shaft can be short; in fact so short that the bosses butt against each other. This double universal joint arrangement can be seen in the final drive of articulated earth-moving machinery with all-wheel-drive.


Rear-wheel- drive vehicles have UJs at either end of their tail shaft, taking the drive from the gearbox to the differential. The gearbox shaft and the differential pinion shaft are kept parallel as much as the rear suspension will allow, and the forks of these UJs must be aligned as already explained. The arrangement can often be viewed on large trucks where the driveline is exposed.

Speed variation is the reason why UJs are not used in the drive shafts of front-wheel-drive vehicles. So-called Constant Velocity (CV) joints are used instead, to allow the front wheels to steer while the wheels are being driven. However, CV joints are expensive to manufacture and are not available in the small sizes needed for Meccano models.

Mick Berg      (at 7:35am, Fri 19th Oct, 18)

Very interesting info. Thank you!

Your name:
Your message:
Security check: (Please type in the text to prove you're a person!)
Login status:  You have not yet entered your user name and password. You cannot create or edit documents until you do.
Enter your user name and password to log in

Remember me

If you click on the box marked 'remember me next time', you will not have to log in again on this computer for three months.

If you don't have a user name yet, please click here


(Neil Bedford and Richard Smith)
Midlands Meccano Guild
Model Report 
97th Meeting 
The Arduino Sketch 
(Philip Drew & Richard Smith)
Midlands Meccano Guild
105th Model Report 
92nd Model Report 
91st Model Report 
103rd Meeting Model Report 
(John Rogers & Colin Bull)
Midlands Meccano Guild
101st Meeting Model Report 
(John Rogers and Neil Bedford)
Midlands Meccano Guild
100th Meeting Model Report 
98th Meeting Model Report 
97th Meeting Model Report 
(David Couch)
The Little Tram
An introductory Arduino project 
82nd Meeting Model Report 
(Roger Marriott)
Midlands Meccano Guild
95th Meeting Model Report 
(Andre Theberge)
Meccano Segway
(Andre Theberge)
A Meccano Segway
Arduino code 
(Andre Theberge)
A Meccano Segway
Assembly instructions 
92nd Model Report 
91st Model Report 
76th Meeting Report 
Construction details 
Bert Love's Blocksetter in colour 
(Rob Thompson pp Terry Bullingh)
BlockSetter Tower
Built by Terry Bullingham 
(Rob Thompson pp John Reid)
Captain Robert Falcon Scott
1912 Polar Sledging Party 
(Niels Gottlob)
Bucket Wheel Excavator
Transcribed from typed document with photos 
(Norbert Klimmek)
Hulett Ore Unloader
A 1 to 32 Scale Model 
(Joe Attard of Malta)
A model ship
Not many in this condition I'll bet! 
 View all | Chat | Models | Hints and Tips | Opinion | Reviews | Mine