Top Home Bottom

Parts 36 - 36b: Screwdrivers

A simple bent or stamped screwdriver was provided in almost all Meccano outfits.  It wasn't much good, to be honest.  Most boys commandeered one of Dad's from the toolshed.  The exception was the excellent longer or special screwdriver supplied in the largest outfits from 1920 onwards.  These are now quite rare, because more often than not Dad commandeered them for his toolshed.

36	Screwdriver	1901	1978	1	1	1	N°00
36a	Screwdriver, extra long	1920	1975	0	0	1	N°8
36b	Special screwdriver (steel)	1928	1941	1	1		n/a
36b	Screwdriver (plastic)	1972	-				n/a

The parts

At the left of the picture (marked A) is a range of standard screwdrivers, supplied in almost all outfits except for the extremely small 000 and Pocket Meccano outfits. 

The larger or special screwdriver is somewhat more complex.  Initially, part 36a had a wooden handle and was only supplied as a spare part until it was added to outfits 5 and above in 1922.  In 1923, it changed to a long bent rod, not a very elegant replacement.  In 1928, the part 36b Special Screwdriver B, the most elegant of all the Meccano screwdrivers, was introduced and supplied instead of the 36a in outfits 5 to 7, and later in outfits G, H, K, and L from 1934 to 1937, and outfits 8, 9, and 10 pre-war.

The reintroduction of the larger outfits in the late 40's saw the 36b disappear, and a new wooden-handled version of the 36a replaced it in outfits 8 and above (C).  This remained in place until 1975.  (The outfit 8 of the 70's had been downgraded to the contents of the previous outfit 7, so the special screwdriver was only supplied in outfits 9 and 10 in the 70's).

Meanwhile, part umber 36b had been reinstated, as a plastic-handled screwdriver available in the Super Tool Set from 1968 and and new version in the Multikits from 1973.  This went through more than one form, finishing with the pear-shaped version shown at D above.

In 1975, part 36a (the wooden screwdriver) was discontinued, and outfits 9 and 10 instead are shown as having the new plastic part 36b (D above).  In 1978, the standard screwdriver part 36 was discontinued and all Meccano outfits (including Multikits) were supplied with a new flat-handled version of the plastic screwdriver part 36b (E). In fact, the dark blue/dark yellow outfits 9 and 10 of the period 1978-79 were supplied with what was presumably old stock of the thicker version of part 36b (D).

Chronological variations

The standard screwdriver went through four major variations, as follows:

• From 1901, 6swg rod bent with a triangular handle
• From 1912, stamped from flat plate, triangular form, with or without cutout.
• From 1916, stamped from flat plate, rounded end form, with or without cutout.
• From 1922, familiar 8swg rod bent with a teardrop handle, shorter post-war.

Comparison with the page for part 34 will clearly show that the combined spanner/screwdriver part 34a comes from the cutout in the two middle variations. The earlier fat 34a is from the triangular form above, and the later thinner 34a from the rounded end form (1916 on).

There are various detailed changes within each of these four major variations, each of which is shown in detail in the table at the bottom of the page.

The 8swg bent rod screwdriver went through some well-defined periods. The earliest versions are stamped "Meccano" near the tip, this disappeared in the mid 30's. The overall length of the screwdriver varies from one example to the next (because of the method of manufacture), but pre-war ones are noticeably longer, around 13cm overall. Post-war screwdrivers are around 12cm or slightly less. The change to a cut-off (rather than pointed) end to the rod happened near the end of the nickel period, some time in the 60's.

The details of variation in the larger screwdrivers is described above and detailed below, but bear in mind that the part number swapped from 36a to 36b through the period (in the major outfits), and in the 70's more than one type of screwdriver was supplied in different themed sets outside of the period in which they existed in the 10-outfit. 

Variations and oddities

This picture shows the small yellow-handled electrical screwdriver from 1970, supplied with the 4EL and 5ME outfits and the electronic control set.  It was given the part number 622, and so is not included in the table of part 36's below. 

There are a number of French variations of these screwdrivers.  The wooden 36a had a fluted handle with a large steel ferrule.  This image shows the French "Meccakit" orange-handled screwdriver, introduced in 1976 with a chrome-plated blade.  This screwdriver was included in the the two largest French Meccakits (French counterparts to UK Multikits), respectively Meccakit Travaux Publics 300 (Highway) and Meccakit Grues 400 (Crane). 

Dealer spare parts boxes

The picture shows a wooden screwdriver (part 36a) and its brown paper wrapping, with a white label showing the part number, which dates it from the early 60's. 
Screwdrivers are very rarely seen in yellow boxes and there would surely not have been many boys who would have bought a part 36 screwdriver from the Meccano dealer. But William has found a box! Pity the dealer who bought these...

Individual part numbers

Part numbers for the parts on this page are as follows:    Unique part numbers
For identification, each variation has been given a suffix to the main Meccano part number. These suffixes consist of a two-character code for the colour, and if there are many variations, a further number and sometimes letter code to identify each variation. See the bottom of the 'Parts' page for further details.

You don't need to worry what the codes are, just click on any one for a photograph.

The button above turns on and off the display of DMS numbers (where they are known). The DMS (Development of the Meccano System, Hauton and Hindemarsh) published in 1972 and added to in 75 and 82, suggested part numbers for every variation of every Meccano part. These numbers aren't perfect, but they are recognised and also referenced in the EMP (Encyclopedia of Meccano Parts, Don Blakeborough).

Description	from	36	36a	36b
Squat wooden handle with bulbous end ¹	01	.mm
6swg rod, triangular handle, 5 1/8'' long	07	.mm1
6swg rod, triangular handle, black, stamped Meccano	??	.mm1b
6swg rod, triangular handle, bronzed, stamped Meccano	??	.mm1c
6swg rod, triangular open handle, black, stamped Meccano	??	.mm2
Triangular stamped plate with cutout and indented, nickel	12	.ni2
Triangular stamped plate with cutout and indented, black	13	.bk1
Triangular without cutout, indented, nickel, stamped Meccano	??	.ni2a
Triangular with cutout, not indented, nickel, stamped Meccano	??	.ni2b
Large rounded plate, with cutout and indented, black	16	.bk2
Large rounded plate, with cutout, not indented, black	??	.bk2a
Large rounded plate, with cutout, not indented, bronzed	??	.xx
Small rounded plate, no cutout, hole in end, nickel	20-22	.ni3
Small rounded plate, no cutout, hole in end, black	??	.bk3
Small rounded plate, no cutout, no hole in end, nickel	??	.ni3a
Small rounded plate, no cutout, no hole in end, black	??	.bk3a
8swg rod, teardrop handle with pointed end, ~13cm, nickel	22	.ni4
8swg rod, teardrop handle with pointed end, ~13cm, black †	39-41	.bs4
8swg rod, teardrop handle with pointed end, ~12cm, nickel	45	.ni
8swg rod, teardrop handle with pointed end, ~12cm, black †	51-52	.bs1
8swg rod, teardrop handle, cutoff end, nickel	62?	.ni1
8swg rod, teardrop handle, cutoff end, nickel, parallel tip †	??	.ni1a
8swg rod, teardrop handle, cutoff end, zinc, parallel tip †	??	.zn1
8swg rod, teardrop handle not closed off, zinc plated	66-78	.zn
Wooden handle, 4'' blade (all from here on have parallel tip)	20-23		.xx1
Bent rod handle, 5'' blade	23-41		.ni
Solid steel, nickelled, with detachable blade, 8'' long	28-41			.ni
Wooden handle, 4'' blade, rounded ferrule	47-75		.xx
Wooden handle, 4'' blade, rounded ferrule, black †	51-52		.bs
Wooden handle, 4'' blade, straight ferrule punched	47-75		.xx2
Dark red plastic pear-shaped handle, with recessed lettering ²	67?			.re1
Red plastic ridged handle † ²	69-75			.re
Red plastic pear-shaped handle ²	73-78			.re2
Orange plastic pear-shaped handle	??			.re2a
Orange gloss plastic pear-shaped handle, rounded	??			.re2b
Translucent maroon plastic handle (in Multikits)	75-78			.re3
Red plastic flat pear-shaped handle, zinc blade, small letters	78			.re4
Red plastic flat pear-shaped handle, zinc blade, larger letters	78			.re4a
Red plastic flat handle, iridescent blade	79			.ir
Yellow plastic flat handle, iridescent blade † ³	82			.ye
		ALL	ALL	ALL

¹ There are many examples of similar screwdrivers of this era, but many seem to be much later and from the competing Primus or Singer brands. It is almost impossible with a 100-year-old screwdriver to be sure which box it originated from.
² Rather confusing. Initially the Super Tool Set in 1967 contained (we believe) the .re1 version, changing to the .re ridged version in 1969 (confirmed), also used in the 1972 Clock Kit. The pear-shaped .re2 variation began in 1973 with the multikits, and was also used in the Super Tool Set starting between then and 1975. From 1975, it was also used in the largest outfits 9 and 10 after the demise of the wooden version, making part 36a obsolete. From 1978, the flat version 36b.re4 replaced it in all but outfits 9 and 10.
³ Supplied in "Truckers Fleet Set"

Please send us pictures of missing parts! Hints and tips for pictures
Take a picture of the part in very good light, preferably on a plain yellow background, without a flash but with a tripod.
Ideally, trim the picture to about 150 pixels per inch of the Meccano part (unless the part is particularly big or small), save it as a reasonably good quality jpg file with a filename of exactly the part number, for example 19b.ni1.jpg, and email it to us by clicking on 'Contact us' at the top of the page. Thanks!

• A greyed-out box shows that no part exists for that colour combination.
• Part number codes with a green background have an attached picture of the part, just click once on the code to show a photograph of that part in a separate window.
• Parts marked "†" were temporary or economy parts, or existed only within specific themed outfits. The previous part continued throughout or afterwards.

Further information

Total number of messages on this page: 11.  This is page 2 of 2.   

Martin fay      (at 6:55am, Wed 25th Feb, 09)

Hello.can you please help me locate a yellow handled 622 screwdriver or point me in the right direction Regards Martin Reply: Not particularly sure, you could try hanging around on ebay (and asking questions of those who regularly sell Elektrikit items), or put a wanted at on www.nzmeccano.com/Wantedads.php

Pepín      (at 2:18am, Wed 10th Dec, 08)

Hello again. If the handle measure is exactly 3 inches and the overall length is less than 8 inches (exactly 20 cm.) it may be possible that this 36 b screwdriver was adapted for a french suit cuting the blade. Best regards.

Pepin      (at 6:24am, Tue 9th Dec, 08)

Thanks.The meccano inscription is clearly visible.The date is 1929.Overal length is 20 cm(precisely). The blade is 12'5 cm(3 inches).Nickelled . I've pulled without succes, probably due to the age.

Pepín      (at 12:56am, Thu 4th Dec, 08)

Hello. A possible mistake in scwdriver 36b .ni were the blade is not 8" but 4"? I´ve got one and may look at the detail but yourphoto shows that 8" may be the whole length, not the blade lenght. ¿detachable? How is this posible. Reply: Hi, thanks for the message. The description isn't quite as clear as it could be, but there is a comma. The screwdriver is 8" overall, the blade about 4 as you say. It is detachable -- just pull it! There are some very good reproductions around. Both the shaft and the end of the handle should be stamped Meccano.

Jon vaughan      (at 2:03pm, Tue 25th Mar, 08)

Hi, I have a late French 10 set in a 5 drawer chest, Im guessing its a 1989/1992 set, however the screwdriver is missing. I have tried to find out which type was supplied in that set but I cannot find out a definate answer. Any help/guidence would be appreciated to say the least !Regards jon

Your name:
Your message:
Security check:	(Please type in the text to prove you're a person!)