Top Home Bottom

Part 104: Shuttle

104	Shuttle, for loom	1916	1940	1	1	0

The parts

The Meccano Shuttle was introduced, along with the other special loom parts, in 1916.  It was the most expensive spare part until the Geared Roller Bearing in 1928, and of course has only one use.  We can probably assume that there was a limited market for this part until it was added to the new largest outfit (number 7) in 1921.  It was also supplied in the 7 outfit's replacement (the Outfit L) in 1934. 

With the new numeric outfits 1 to 10 in 1937 the shuttle and many of these special parts were dropped, although it was still available as a spare part until production stopped in 1941.  It was never reintroduced.

Chronological variations

There are two common varieties of the shuttle.  The difference is fairly obvious – the earlier ones have a groove down each side and a plain rod as a bobbin.  Later versions lose the grooves, but gain flanges on the bobbin to help the thread stay in place.  It is believed that this change dates from around 1930.  Well-dated outfits of 1929 have the earlier type stamped MFEA, and 1933 the later type.

DMS/EMP show an earlier type, from 1916 to 1920, with a much simpler design.  The bobbin is held by two hooks from a much plainer frame.  More information on this would be interesting, if anyone has one.

Within the first type, I have noticed at least three clearly different variations.  They are shown in the picture to the right.  On the left is a very sharp-cornered shuttle, stamped Meccano twice in a circle.  In the middle is a similar type, but with all the edges considerably more rounded, including at the transition to the shaped end.  This middle one is stamped MFEA, dating it from between 1921 and around 1929.  The right-hand version is even more rounded, with longer and smoother points at each end, stamped only Meccano.

It would be interesting to research which of these varieties is the most common, and whether we could attach any further dates to them.

Variations and oddities

Dealer spare parts boxes

Well would you believe it? Here's a picture of an extremely rare boxed shuttle, courtesy of Dave Taylor and Richard Payn.  You might as well remember what this looks like as it's unlikely you're going to see another one!

Individual part numbers

Part numbers for the parts on this page are as follows:    Unique part numbers
For identification, each variation has been given a suffix to the main Meccano part number. These suffixes consist of a two-character code for the colour, and if there are many variations, a further number and sometimes letter code to identify each variation. See the bottom of the 'Parts' page for further details.

You don't need to worry what the codes are, just click on any one for a photograph.

The button above turns on and off the display of DMS numbers (where they are known). The DMS (Development of the Meccano System, Hauton and Hindemarsh) published in 1972 and added to in 75 and 82, suggested part numbers for every variation of every Meccano part. These numbers aren't perfect, but they are recognised and also referenced in the EMP (Encyclopedia of Meccano Parts, Don Blakeborough).

Description	from	104
Nickel plated shuttle, plain rod	??	.ni
No side grooves, bobbin with flanges and spring	30	.ni1
		ALL

Please send us pictures of missing parts! Hints and tips for pictures
Take a picture of the part in very good light, preferably on a plain yellow background, without a flash but with a tripod.
Ideally, trim the picture to about 150 pixels per inch of the Meccano part (unless the part is particularly big or small), save it as a reasonably good quality jpg file with a filename of exactly the part number, for example 19b.ni1.jpg, and email it to us by clicking on 'Contact us' at the top of the page. Thanks!

• A greyed-out box shows that no part exists for that colour combination.
• Part number codes with a green background have an attached picture of the part, just click once on the code to show a photograph of that part in a separate window.
• Parts marked "†" were temporary or economy parts, or existed only within specific themed outfits. The previous part continued throughout or afterwards.

Further information

Total number of messages on this page: 10.  This is page 2 of 2.   

Henk Brouwer (meccanoland)      (at 1:39pm, Sun 13th Feb, 11)

I think that you should add the wooden shuttle to the table you can find a example in my user gallery period 1907-1921

Tony Brown      (at 6:44am, Fri 19th Mar, 10)

I have absolutely now way of knowing if this story is genuine or not but I have a shuttle given to me by a friend in Liverpool that I was told was made in the factory during the 'sit-in' following the problems with the company.

Meindert D. Buis      (at 7:36am, Tue 26th Jan, 10)

I want to make by myself this item on mij lathe. Because the price is in Europe more than € 60,00. I am searching voor de right dimensions length, width en hight. Can you help me, please. Kind regards Meindert D. Buis Emmastraat 37 1432 EW Aalsmeeer The Netherlands

Meindert D. Buis      (at 7:36am, Tue 26th Jan, 10)

I want to make by myself this item on mij lathe. Because the price is in Europe more than € 60,00. I am searching voor de right dimensions length, width en hight. Can you help me, please. Kind regards Meindert D. Buis Emmastraat 37 1432 EW Aalsmeeer The Netherlands

Your name:
Your message:
Security check:	(Please type in the text to prove you're a person!)