Home | Links | Contact |

Printed from www.nzmeccano.com

Top Home Bottom

My E15R Motor

(Author: Arup Dasgupta (ISM 652))

A repair story

Figure 1: The E15R Motor with box and leaflet

I always wanted a Meccano electric motor. The cricket ball motor was available in the 50’s in India but at a cost which was beyond my modest means. So recently, when I found an E15R available on eBay, and I had just conquered my fear of using my credit card on eBay with PayPal to protect me, I decided to make a bid. In fact I went whole hog and bid for an E15R, a Crane Motor and a six speed Power Drive motor as well. I usually lose most bids on eBay because the ending is when I am fast asleep and I haven’t mastered all those bidding tricks, so I get outbid. But these were different. They were ending at 11 pm so I could take care of any snipers. But I needn’t have worried. The recession is not all that bad. There were no more bids, so I won all three.

The E15R and Crane motor were from the same seller and I got them in a week’s time. The Crane motor worked well but the E15R refused to budge. I could feel the rotor lock so it was electrically live. A few drops of oil on the armature shaft got the motor going for about two seconds before it jerked to a sudden stop with a ‘oh oh’ kind of a clunking noise. Close examination showed that one side of the armature winding had come off the commutator. It was rather poorly soldered to begin with and the long journey plus the spin up caused it to give way.

Figure 2: The motor disassembled. Note the black stuff on the commutator and the disconnected armature winding with a blob of solder at its tip. The motor was otherwise quite clean

Closer examination revealed a brush that bashfully retreated into its holder at the slightest opportunity. The commutator was covered with a black sticky layer of something. The brushes were ‘held’ by the lead of a capacitor pushed through the last turn of the brush holding spring. I couldn’t believe my eyes! Had I picked up a lemon? An appeal to Spanner was informative. Richard Payn was of the opinion that the spring was the culprit and the bad news was that springs were impossible to find. Geoff Brown suggested a way to open up the motor and tips on cleaning the brushes. So armed with this information I decided to try and fix the motor.

Removing the four nuts holding the side plate opposite to the side holding the brushes released the side plate and the armature came out easily. I sprayed the commutator with tape recorder head cleaning fluid and used a cotton bud to remove the sticky black layer. It took several sprays and buds before the copper shone through. Next I heated and removed the solder blob from the armature lead that had worked loose. I applied a thin layer of solder on the commutator edge and then soldered back the armature lead. A light application of a needle file was needed to remove the excess solder to ensure that it didn’t foul with the stator.

Figure 3: Close up of the brushes after being teased out of the holders. Note the sticky stuff.

I turned my attention to the brushes. I teased out each brush using a jeweller’s screwdriver and a pair of tweezers. The reason for the ‘bashfullness’ of the brushes became clear. The brushes were coated with the same sticky stuff I found on the commutator. More application of the cleaning fluid removed the sticky stuff and after a few repetitions of this treatment I could make them slide in and out of the holder freely. I sprayed on a coat of ‘Zorrik 88’ recommended for cleaning and lubricating distributor points and spark plugs.

 The rest of the motor was quite clean and did not require any drastic treatment. After the spray dried out, the armature was put back and the brushes teased back using the jeweller’s screw driver to seat them on the commutator. The side plate was replaced and the test run was a success. The commutator still kept getting coated but application of the cleaning fluid on the tip of a cotton bud two three times cleared up the residual contamination.

Figure 4: Reassembly after the repairs. The new solder joint can be seen as well as the brushes, now properly seated

I measured the current drawn from the DC source. No load drain was about 0.6A. Stalling the rotor pushed the drain to 0.8A. I think this is quite normal. So, I now have a motor which I had long desired to own. As I was testing the motor my daughter walked in and asked “what is this smell?” It’s my motor; it’s working and what she was smelling was the ozone!

I have added a few pictures of the steps in the hope that it may help another Meccano-person who may face the same problems. This is a small pay-back for the invaluable help I got from Spanner.

Figure 5: The spinning motor! Can you see the spark between the brush and commutator?

Figure 6: My tools for the job. I use a head mounted magnifier for convenience



Total number of messages on this page: 9.  This is page 1 of 2.   Next

Mel Saunders      (at 2:55pm, Wed 6th Jul, 16)

I just got 2x what I think are E15 motors, from eBay for £6.50, they where in bits, and also had black gunky stuff inside, a good wash in alcahol? did the trick. But i got one together and it runs, but quite noisey!! and I found someone who sells suitable brushes... the other is a bad state and will need lots of TLC I too have pictures if you need to see them. I'm in the UK!


Michael Walker      (at 3:19am, Mon 23rd Feb, 15)

The E15R motor runs from a 15v AC or 12-15v DC power source. At the time these motors were introduced, various brands of model train transformers were easily obtainable, with many offering an adjustable 0-12v DC output for the locomotives, plus a 15v AC outlet for lighting and other accessories. Examples of these were the Hornby Marshall II and III. If a transformer could not be used, the E15R could provide adequate power from a 12v car battery. As the E15R is a 'universal' motor, it doesn't matter which way round you connect the wires from the transformer or 12v car battery to the motor - you won't damage anything.

Paul      (at 10:56am, Sat 21st Feb, 15)

Amazingly stupid question... I've recently acquired two E15R motors, but yet to use them. Reading this I'm concerned that I may connect them up wrongly to the power source. Is that right? Looking at the wiring it looks to me as if reversing the connections would only change the direction of the motor...

' SirGASMASK"      (at 10:11am, Sat 18th May, 13)

I have an old bi polar motor from a 1940's erector set.

josephdemeyer      (at 7:21pm, Sat 28th Jan, 12)

this was, and looks like: still!, the dream engine for every meccano boy/man...so when i was in my teens (and in the early 60's) and finally succeeded convincing my parents that the magic wind up motor really no longer sufficed my meccano ambitions, there it was that X-mas eve! Alas..in my excitement, I reversed the transformer wires and the ensuing millisecond roar, flash and still, fifty (!) years later in my nose lingering smell of burned wires...led to a temporary halt in fulfilling those plans. Thanks to my dear mother- God bless her soul!- the whole damned thing got rewired (can you imagine doing that now?..) by a guy who must have scratched his head: "why am i doing this?"...and yet assured many years of delightful bliss for a boy powering his meccano constructions by this amazing motor. ENJOY!

Arup Dasgupta      (at 6:06am, Mon 9th Jan, 12)

Try eBay. These do come up from time to time.

Your name:
Your message:
Security check: (Please type in the text to prove you're a person!)
Login status:  You have not yet entered your user name and password. You cannot create or edit documents until you do.
Enter your user name and password to log in

Remember me

If you click on the box marked 'remember me next time', you will not have to log in again on this computer for three months.

If you don't have a user name yet, please click here

Latest documents:

(Neil Bedford and Richard Smith)
Midlands Meccano Guild
Model Report 
97th Meeting 
The Arduino Sketch 
and how to upload a Youtube or Vimeo video to the Gallery 
(Paulo Kroeff de Souza)
"Homemade" Screwed Rods
(Paulo Kroeff de Souza)
The Meccano driving band problem
(Paulo Kroeff de Souza)
Meccano Cord Reproduction
(Paulo Kroeff de Souza)
Substitutes for parts 142 and 155
(Philip Drew & Richard Smith)
Midlands Meccano Guild
105th Model Report 
92nd Model Report 
(Neil Bedford and John Rogers)
Midlands Meccano Guild
104th Model Report 
91st Model Report 
103rd Meeting Model Report 
by Peter Stuart, Meccano Modellers Association Sydney Inc 
(Richard Smith and Neil Bedford)
Midlands Meccano Guild
102nd Meeting Model Report 
(John Rogers & Colin Bull)
Midlands Meccano Guild
101st Meeting Model Report 
Spanner Challenge 
(John Rogers and Neil Bedford)
Midlands Meccano Guild
100th Meeting Model Report 
A G gauge model 
(Colin Bull & Richard Smith)
Midlands Meccano Guild
99th Meeting Model Report 
98th Meeting Model Report 
97th Meeting Model Report 
(David Couch)
The Little Tram
An introductory Arduino project 
(G. Eiermann and M. Schild)
A Short History of MARKLIN Metall
96th Meeting Model Report 
83rd Meeting Model Report 
82nd Meeting Model Report 
Picks up three golf balls 
(Roger Marriott)
Midlands Meccano Guild
95th Meeting Model Report 
The Spanner Challenge 
94th Meeting Report 
(Andre Theberge)
Meccano Segway
(Andre Theberge)
A Meccano Segway
Arduino code 
(Andre Theberge)
A Meccano Segway
Assembly instructions 
(Michael J. Walker)
Meet the new MMG President
Geoff Wright 
The Spanner Challenge 
(Michael Walker)
Midlands Meccano Guild
93rd Model Report 
Report by Michael J. Walker. 
92nd Model Report 
(Stan Knight)
Minimal Meccano
Pocket Meccano Sets of the 1970s 
Little Lever, Bolton 
The Spanner Challenge 
91st Model Report 
(Bob Thompson)
Back to the beginning
Shop Display Model 
90th Meeting Report 
(Old Blue Gold)
Getting Old
A screwy story 
The Spanner Challenge 
Model report written by Michael J. Walker 
76th Meeting Report 
Exhibition in Nelson, New Zealand 
(Barry Gerdes)
Meccano Radio
How to flatten  
(Rod Socket)
Dear Mrs Spanner
Survival techniques for the Meccanoman's wife 
(Stan Knight)
The Top Ten Tools
Indispensable Tools for the Meccanoman 
A call for help 
The Spanner Challenge 
For small brass and nickel parts. Also for stripping paint and rotted zinc plating. 
(Stephen Heafield)
Waterslide Transfers
Refurbishing 0 & 00 Aero Models 
Construction details 
or Put Your Hammer Away 
Mobile Morris Crane from 1968 MM 
Bert Love's Blocksetter in colour 
The dangers of internet auctions 
(Rob Thompson pp Terry Bullingh)
BlockSetter Tower
Built by Terry Bullingham 
(Rob Thompson pp John Reid)
Captain Robert Falcon Scott
1912 Polar Sledging Party 
(Niels Gottlob)
Bucket Wheel Excavator
Transcribed from typed document with photos 
Selected Spanner messages 18th to 24th January 
Selected Spanner messages 11th to 17th January 
Selected Spanner messages 4th to 10th January 
(Norbert Klimmek)
Hulett Ore Unloader
A 1 to 32 Scale Model 
(Joe Attard of Malta)
A model ship
(Arup Dasgupta (ISM 652))
My E15R Motor
A repair story 
About Meccano
What is Meccano? 
Thoughts about modern Meccano 
Some hints and tips 
Not many in this condition I'll bet! 
 View all | Chat | Models | Hints and Tips | Opinion | Reviews | Mine